Skip to main content

Hardware needed to run ZeroShell

Hardware needed to run ZeroShell
Zeroshell works on x86 and x86_64 box with at least a Pentium 233MHz, 96MB RAM, an ATA CDROM reader or an ATA Compact Flash (CF) adapter if you prefer to boot from this type of medium (for example on embedded devices).
Every VGA graphic card and RS232 serial port are supported.
The database in which data and configuration are saved can be stored on IDE, SATA, SCSI and USB storage devices.
All the PCI, USB and PCMCIA network cards supported by the Linux kernel are supported by ZeroShell too and should work correctly. For a few Network adapters, Linux has not support for VLAN 802.1q. In this case ethernet packets greater than 1496 bytes are not forwarded on the VLANs.
Hardware tested and known to work
Wireless Router Application Platform (WRAP)These nice and cheap small computers for network appliances need of a custom CompactFlash image.
ALIX.2* with 256MB of RAM, AMD Geode LX CPU 500MHz processor and MiniPCI expansion slotsALIX systems, with their dimension (15cm x 15cm), low cost and power requirement are convenient platforms to install Zeroshell. The ALIX architecture is very similar to the WRAP architecture (but much faster) and hence you need of the WRAP CompactFlash image to boot Zeroshell that you can find in the download section.
Mini-ITX EPIA-SP8000E
Mini-ITX EPIA-SP13000These are two small (17x17cm) motherboards produced by VIA Technologies, Inc. with VIA Nehemiah 800/1300Mhz CPU, video card, network card, sound card, USB, SATA and IDE controllers integrated.ZeroShell is developed on Mini-ITX EPIA-SP8000E system.
Soekris Net4801 produced by Soekris Engineering and based on an up to 266 Mhz CPU. This small and lower-power computer has 3 Fast Ethernet ports (VLAN 802.1q compliant) and is a good solution for small routers, transparent bridges, firewalls, VPN boxes, Captive Portals and other network appliances.

Popular posts from this blog

TBS5520 Multi-standard TV Tuner USB Box review

Noul TBS5520 Multi-standard TV Tuner USB Box a celor de la TBS se foloseste de RafaelMicro R848 multi-standard tuner si  AVL6882 Demodulator pentru a reda urmatoarele standarde: ETSI EN 302-755 V1.3.1 (DVB-T2/T2-Lite) ETSI EN 300-744 V1.6.1 (DVB-T) ETSI EN 300-429 V1.2.1 (DVB-C) ETSI EN 307-421 V1.2.1 (DVB-S2) ETSI EN 300-421 V1.1.2 (DVB-S) ARIB STD-B31 V1.6-E2 (ISDB-T) ITU-T J.83 Annex B 12/2007 (J.83/B) http://www.tbsdtv.com/products/tbs5520_multi-standard_tv_tuner_usb_box.html Pe aspectul fizic nu insist, sunt destule fotografii pe internet, vreau doar sa punctez cateva aspecte: pentru alimentare este necesar cablu Y USB - este singura modalitate de a furniza energie si de aici avem o limitare in ceea ce priveste functionalitatea cu motor HH mobilitate sporita si posibilitatea alimentarii directe din bateria unui notebook sau chiar conectarea la Tableta Android (de indata ce driverele vor fi gata) “TBS 5520 USB2.0 in warm state” nici rece dar nici fie...

VoIP: Totul pana la securitate

Corporatiile care implementeaza tehnologii voice over IP (VOIP) cu scopul de a reduce costurile de comunicatii nu ar trebui sa piarda din vedere riscurile de securitate care ar putea aparea la confluenta vocii cu datele. Cel putin asa sustin analistii de securitate. Majoritatea utilizatorilor care apeleaza la VOIP sunt in primul rand preocupati de calitatea vocii, potentialitate si interoperabilitate. Toatea acestea sunt aspecte fundamentale de calitate a serviciilor pe care companiile trebuie sa se asigure ca le obtin chiar inainte de a decide sa migreze catre VoIP. Insa unele organizatii de securitate ii avertizeaza pe utilizatori in privinta pericolelor ce se ascund in spatele serviciilor VoIP nesecurizate, apreciind ca fara a lua in consideratie aspectul securitate,VoIP nu va reusi niciodata sa-si faca loc in zona corporate. Prin VoIP, traficul de voce este transportat printr-o retea de date cu comutatie de pachete prin intermediul Internet Protocol. Retelele VOIP trateaza vocea ca...

Installing Backtrack 3 under VirtualBox - Part 2

10.): In the "General", "Settings", "Advanced" tab you should do the following: Click the "Boot Order", "Floppy" checkbox to uncheck it. The "CD/DVD-ROM" should be the first boot device (for installation only). You can leave the "Boot Order", "Hard Disk" checkbox checked, you will re-order the drives later. Leave the "Extended Features", "Enable ACPI" checkbox checked. Click the "Extended Features", "Enable IO APIC" checkbox to make it checked. If you have a newer CPU then click the "Extended Features", "Enable VT-x/AMD-V" checkbox to make it checked. Click the "Extended Features", "Enable PAE/NX" checkbox to make it checked. Choose "Bidirectional" for the "Shared Clipboard" setting. Choose "PIIX4 for the "IDE Controller Type" (PIIX3 does not implement an SMBus or I2C bus). Change the "Sna...